Dimming LED

Posted on December 17th, 2014 in category "Tips"

DimmingCan I dim LED? Was the most frequently asked question in 2014. For the most part the answer is yes, but first you must do your research. Every manufacturer’s LED array (light emitting diodes mounted in an array on a circuit board) or LED light bulb may have different dimming requirements.

Most (but not all) screw-in LED light bulbs are compatible with standard incandescent dimmers. Compatible means that the bulbs can be dimmed, although the bulb’s dimming performance may not match what you’re used to seeing when dimming an incandescent or halogen bulbs. Depending on the quality of the bulb you select, compatible bulbs may still:
– have less dimming range than an incandescent or halogen bulb
– dim less smoothly than an incandescent or halogen bulb
– flicker or shimmer at certain light levels
– buzz

Let’s review some dimming basics:

Line-voltage (120V) incandescent and halogen lamps use forward phase-control dimming. Resistive – rated for cold filament inrush, the positive and negative periods may not be equal. The lamp is energized only during the last portion of each power-line half cycle. Forward phase dimming uses robust electronics, is suitable for most loads, including incandescent, tungsten halogen, as well as some types of LED power supplies.

Magnetic low voltage lighting transformers (MLV) use symmetric forward phase-control dimming. Inductive – symmetric cycles, the positive and negative periods are equal. MLV dimmers are required for all low-voltage lighting using magnetic low-voltage transformers regardless if the lamp is halogen or LED.

Electronic low voltage lighting transformers (ELV) use reverse phase-control dimming. Capacitive – the lamp is energized during the initial portion of each power-line half cycle. Reverse phase dimming uses more complex electronics (solid state). ELV dimmers are required for all low-voltage lighting using electronic low-voltage transformers regardless if the lamp is halogen or LED.

LED (Light Emitting Diode) & Electronic LED Drivers. All LEDs (arrays and lamps) require drivers to operate. LED drivers work similar to low-voltage transformers. The LED light source must be matched to the LED driver and every manufacturer will differ. Some LED fixtures have the LED driver built-in as an integral part of the fixture, others supply a remote mounted driver, and LED lamps have the driver built into the base of the lamp.

Dimmers are designed to send power and control signals to the LED driver. This is where you must do your research, especially if you are using more than one type of LED on a circuit. Check the recommendations of the manufacturer; check both the LED/Driver and the Dimmer specifications. Some LED drivers use incandescent (forward phase), some use MLV (symmetric forward phase), some use ELV (reverse phase) and some use 0-10V dimmers.

Ok…we threw you a loop on that last one, 0-10V dimming, we have not discussed that yet. 0-10V is an analog lighting control protocol; applies a voltage between 0V and 10V to produce varying intensity levels. There are two types of 0-10V controls: a current source (theatrical dimming) and the more common, current sink (fluorescent ballasts).

Many LED drivers use the current sink 0-10V dimmers. One tip here: 0-10V is a 5-wire system (black, white, 2 control wires & ground) this is important to know in advance so your contractor can pull the correct amount of wire from the fixture to the dimmer. 0-10V dimmers will give you more control and a better dimming range.


Holiday Lights

Posted on December 4th, 2014 in category "Tips"

HolidayBlogMany of us will soon be hanging Holiday lights; the season is upon us! Sometimes we get busy and forget to put safety first, here are a few do’s and don’ts:

Do – throw away those old lights and replace them with LED. LED Holiday lights use a fraction of the energy, they are cool to the touch, they will outlast the old incandescent lights and they have great intense color.

Do – make sure the lights are rated for outdoor use when installing outdoors.

Do – use only outdoor rated extension cords.

Do – plug the lights into a ground fault circuit interrupter (GFCI) outlet or use extension cords with a GFCI on the cord.

Do – use plastic hooks instead of metal, staples or nails.

Do – tuck cords away out of the reach of children and small pets. Avoid running cords under carpets.

Don’t – connect too many strings of lights together. Be sure to read the manufacturer’s recommendations.

Don’t – plug one plug strip into another. Plugs strips are not approved to be joined together.

Don’t – leave the lights up over 90-days. Holiday lights are approved for temporary installations only.

Do – be safe and have a great Holiday Season!


Shop Local!

Posted on November 29th, 2014 in category "Uncategorized"

ShopLocalPortlandStop by and shop local! Many items on sale, while supplies last. We are open until 5:00pm for Shop Local Saturday!


Le Klint Turns 70!

Posted on November 1st, 2014 in category "Uncategorized"

21397_101Good design never goes out of style. And the iconic Le Klint series is the perfect example as it celebrates its 70th anniversary! Le Klint model 101 designed by Kaare Klint was launched in 1944 and it continues to shine. The hand-folded sculptural pendant is made from color-stabilized white PVC which is washable and anti-static. Available in three sizes with the original and authentic hang-up hardware. Click here to see more Le Klint models.


Lamp Sale!

Posted on October 23rd, 2014 in category "New"

LampSale2014Now for the fine print: In-store only. While supplies last. Display items sold “as is”. All sales final. No other discounts apply.


1 2 3 6